Censorship?

 Censorship?

Well now, after being reasonably ignored for quite some time now, apparently the PIETECH BUILDER’S MANUAL seems to have caught some unwanted attention. Out of sheer convenience, I decided to use the eBay platform as a service for interested people to purchase the manual. After being listed for just two weeks, the listing has suddenly “disappeared” completely from eBay and erased from their archives. After speaking with a genuine human being at eBay they now claim that I must have never had such a listing as they show NO ACTIVITY on my seller account over the last 90 days. Since at the time of this writing, it was listed on eBay 15 days ago and I still have the link to the now non-existent listing saved, both on the PIETECH web page and other media as well, I am very certain that it wasn’t a dream.

This, of course, happened on the same day that YouTube issued another crack-down on anyone speaking about corruption within the US election, immediately removing entire channels for simply voicing an opinion. These are online corporate strong-arm tactics at their worst and simply underline the need for private web sites to voice those opinions and highlight relevant facts.

Maybe we need to start an old fashioned “web ring” as a “No Censorship Zone”.

I have experienced this type of censorship before, but I really was hoping that we as a people had gotten past this covert draconianism (echoes of the “cold war”) but apparently not.

I suppose that I should actually take this as a form of encouragement. After all, if there was “nothing to it” nobody would take the time to censor it and if I weren’t on the right track it would not be perceived as a threat within some corporate-type organization.

I will make a new listing for a place to purchase the manual and I will keep publishing the ongoing work with “reactionless propulsion” as public as possible, after all there is at least some “safety in numbers”.

I will also begin the creation of a private online store so that the likes of eBay and Amazon will have no control over what is listed, said, printed or sold. Maybe I will host my own videos as well… We shall see…

Thanks for letting me rant! Good day.

Comments

Post a Comment

Popular posts from this blog

Vol 2, Page 13, Ground Testing

Image
  Post vehicle, wheeled, ground-testing. After a short pause caused by things in life that have required my undivided attention, I’m back & ready to get busy.   So, the on-road testing would be considered a success, and the “hybrid-assist” effect is undeniable. The “failures” encountered within that round of testing were due to the prototype building methods and materials. It is hard to justify the cost in time and materials for a more durable build when it is being taken apart and changed multiple times. Total cost of materials for a single planet gear, without the weight, is around $8 US. The cost of a machined, straight toothed, drilled hole center, spur gear of the same size is around $200 to $300 US. In that light, the component failures are an acceptable offset to the cost differential. Now we move forward with further testing of the PIE 2.0 while still getting ready to build a next version.  ****************************************************************************
Read more

Vol. 2, Page 3, Preparing Parts for PIE 2.0, Second New Weight -Build and Test-

Image
Newest Weight Ready for Testing Building the revised PIE, version 2.0, is well under way. There are two weights are virtually ready for testing. The gears are looking as good as they ever will, and the base has been partially modified to accommodate the revisions in the configuration. I have decided that the drive system will be using #40 roller chain & sprockets. The sprockets and chain are available at a very reasonable price from surplussupply.com. It is too bad that they do not have spur gears to use for the sun & planet gears as well. Regardless, I am getting as much done as feasible while I wait for the sprockets arrive (I already have chain).   I am planning to use a jackshaft, of sorts, to drive the chain. The inexpensive and plentiful components already sourced and obtained will comprise a portion of the jackshaft assembly. I am having a custom shaft machined upon which to fasten the sprocket. A custom shaft would be unnecessary if the shaft, sprocket and availab
Read more