Volume 2 (V2), Page 1, PIE 2.0 Begins

Volume 2 (PIE2.0)…

The rework of many unused parts that are left over from PIE1.0 has begun, along with some newly fabricated pieces for the new unit. Planning for this began about the same time that the first successful demo pulsed its way across multiple work benches.

From the time that first unit moved on its own I have wanted to build a better unit, capable of higher RPMs and running a heavier pendulum weight. Digressing to, and remembering, the 1970s VHS video of Brandson Roy Thornson’s drive pushing a canoe around an Olympic sized swimming pool, that unit had 4 rotating discs (2 CW rotation, 2 CCW rotation) and each had a 5-pound pendulum weight.

PIE 2.0 is going to start out with weights that are around 4.7-pounds. They will not be using any counter-rotating assemblies unless it is deemed absolutely necessary. Yet to be determined is to the number of rotating assemblies, the power source, and speed of rotation (RPMs).

I have about 20 to 25 pictures of various parts, pieces, tools & assorted “junk” waiting to be put to use. Since some find that interesting, I will put some of the pics in this the blog, but will not include them in my personal journal documenting this project.


Base Part in Primer


Chop Saw

Small Drill Press

Spare Motor

Spare Motor

Spare Parts

Lengthened Planet Gear Axle - Revised To Be Used As Stop

PIE 2.0 Weight

Base Part

Planet Gear Needing Re-Work

Planet Gear With Long Pivot Bolt

2 Flexplates & Assorted Junk

Mocking up PIE 2.0

Mocking up PIE 2.0

Mocking up PIE 2.0

Pieces & Parts

Weighing As We Go

Digital Scale is More Accurate


Setting Up Revised Stop On Planet Gear

What a Mess!


Comments

Post a Comment

Popular posts from this blog

Vol 2, Page 13, Ground Testing

Image
  Post vehicle, wheeled, ground-testing. After a short pause caused by things in life that have required my undivided attention, I’m back & ready to get busy.   So, the on-road testing would be considered a success, and the “hybrid-assist” effect is undeniable. The “failures” encountered within that round of testing were due to the prototype building methods and materials. It is hard to justify the cost in time and materials for a more durable build when it is being taken apart and changed multiple times. Total cost of materials for a single planet gear, without the weight, is around $8 US. The cost of a machined, straight toothed, drilled hole center, spur gear of the same size is around $200 to $300 US. In that light, the component failures are an acceptable offset to the cost differential. Now we move forward with further testing of the PIE 2.0 while still getting ready to build a next version.  ****************************************************************************
Read more

Vol. 2, Page 3, Preparing Parts for PIE 2.0, Second New Weight -Build and Test-

Image
Newest Weight Ready for Testing Building the revised PIE, version 2.0, is well under way. There are two weights are virtually ready for testing. The gears are looking as good as they ever will, and the base has been partially modified to accommodate the revisions in the configuration. I have decided that the drive system will be using #40 roller chain & sprockets. The sprockets and chain are available at a very reasonable price from surplussupply.com. It is too bad that they do not have spur gears to use for the sun & planet gears as well. Regardless, I am getting as much done as feasible while I wait for the sprockets arrive (I already have chain).   I am planning to use a jackshaft, of sorts, to drive the chain. The inexpensive and plentiful components already sourced and obtained will comprise a portion of the jackshaft assembly. I am having a custom shaft machined upon which to fasten the sprocket. A custom shaft would be unnecessary if the shaft, sprocket and availab
Read more

Censorship?

  Censorship? Well now, after being reasonably ignored for quite some time now, apparently the PIETECH BUILDER’S MANUAL seems to have caught some unwanted attention. Out of sheer convenience, I decided to use the eBay platform as a service for interested people to purchase the manual. After being listed for just two weeks, the listing has suddenly “disappeared” completely from eBay and erased from their archives. After speaking with a genuine human being at eBay they now claim that I must have never had such a listing as they show NO ACTIVITY on my seller account over the last 90 days. Since at the time of this writing, it was listed on eBay 15 days ago and I still have the link to the now non-existent listing saved, both on the PIETECH web page and other media as well, I am very certain that it wasn’t a dream. This, of course, happened on the same day that YouTube issued another crack-down on anyone speaking about corruption within the US election, immediately removing entire chan
Read more