PIETECH P. 5 - Upcoming Manual, Website, and Continuing the PIE 4.3

 

I apologize for the time lag since my last posting, life tends to get in its own way sometimes but we all do what we have to do. 

Website & Manual: I am building a website for my little consulting firm focusing on the R&D side as well as the PIETECH manual (basically complete, getting finishing touches now). There will also be access to companion videos. That access will only be available with the purchase of a manual. The address to the website is http://www.stclairtech.tech it is online now but I hope to have it truly functional in the next 3 weeks.

At this point in time, the manual (and its companion videos) will be the only information that is not completely free. This will hopefully help offset some of those constantly inflating costs.

A Kit?: Another possibility which came to me as a suggestion is that of a functioning miniature model kit. The kit may be a partially assembled, or only contain the finished pieces. That idea is still only on the drawing board for now until the logistics can be fully worked out.

PIE 4.3 Current Progress: I have taken the PIE 4.3 apart to replace the drive pulley with a chain sprocket. This has given me the opportunity to analyze the unit looking for weaknesses and damage.



Disassembled PIE 4.3

Broken Outer Stop

Broken Outer Stop

It is very apparent that the outer stops were the first weak point, and once they would break there was a cascade effect of failures. The weight would, at times, be allowed to collide end first into the inner stop (sun gear axle). This caused enough deflection in the wheel and axle that the planet gear could skip a few teeth and become “out of time” with the assembly. Now that the 4.3 is apart I have found that the wheel is slightly bent (about 3mm or 1/8”) which is not enough to need replacing yet. The axle is also bent, and that is now definitely scrap metal, There are vides posted to YouTube and BitChute describing the process and showing the bent axle. 

YouTube: https://youtu.be/wmoc2-1v43A 

BitChute: https://www.bitchute.com/video/rfK5qGGRDffR/

I have also received 2 new gear-motors for the PIE 4.3 which are all set up to run at approximately 300 RPMs at 24 volts DC. I am seriously considering running 2 wheels, each with their own drive motor. That may be overkill, but right now design simplicity is very important for the purpose of easy transitioning into the testing phase. 

New Motor

It is reasonably simple to set up a chain drive that would spin the wheels in opposite directions (obviously planning opposing wheels) and they would obviously always be in-sync with each other, but there are other testing considerations like running wheels at different speeds and easily being able to reverse either wheel’s rotation.

Comments

Post a Comment

Popular posts from this blog

Vol 2, Page 13, Ground Testing

Image
  Post vehicle, wheeled, ground-testing. After a short pause caused by things in life that have required my undivided attention, I’m back & ready to get busy.   So, the on-road testing would be considered a success, and the “hybrid-assist” effect is undeniable. The “failures” encountered within that round of testing were due to the prototype building methods and materials. It is hard to justify the cost in time and materials for a more durable build when it is being taken apart and changed multiple times. Total cost of materials for a single planet gear, without the weight, is around $8 US. The cost of a machined, straight toothed, drilled hole center, spur gear of the same size is around $200 to $300 US. In that light, the component failures are an acceptable offset to the cost differential. Now we move forward with further testing of the PIE 2.0 while still getting ready to build a next version.  **************************************************************...
Read more

Vol. 2, Page 3, Preparing Parts for PIE 2.0, Second New Weight -Build and Test-

Image
Newest Weight Ready for Testing Building the revised PIE, version 2.0, is well under way. There are two weights are virtually ready for testing. The gears are looking as good as they ever will, and the base has been partially modified to accommodate the revisions in the configuration. I have decided that the drive system will be using #40 roller chain & sprockets. The sprockets and chain are available at a very reasonable price from surplussupply.com. It is too bad that they do not have spur gears to use for the sun & planet gears as well. Regardless, I am getting as much done as feasible while I wait for the sprockets arrive (I already have chain).   I am planning to use a jackshaft, of sorts, to drive the chain. The inexpensive and plentiful components already sourced and obtained will comprise a portion of the jackshaft assembly. I am having a custom shaft machined upon which to fasten the sprocket. A custom shaft would be unnecessary if the shaft, sprocket and ava...
Read more

Censorship?

  Censorship? Well now, after being reasonably ignored for quite some time now, apparently the PIETECH BUILDER’S MANUAL seems to have caught some unwanted attention. Out of sheer convenience, I decided to use the eBay platform as a service for interested people to purchase the manual. After being listed for just two weeks, the listing has suddenly “disappeared” completely from eBay and erased from their archives. After speaking with a genuine human being at eBay they now claim that I must have never had such a listing as they show NO ACTIVITY on my seller account over the last 90 days. Since at the time of this writing, it was listed on eBay 15 days ago and I still have the link to the now non-existent listing saved, both on the PIETECH web page and other media as well, I am very certain that it wasn’t a dream. This, of course, happened on the same day that YouTube issued another crack-down on anyone speaking about corruption within the US election, immediately removing entire ...
Read more